Buying a Code Marking System: Key Specs to Review

When buying a code marking system, prioritize print resolution, ink compatibility, application speed, and PLC integration. The right specs ensure legible date marks and reduce maintenance downtime on high-speed packaging lines.
- Verify print resolution and ink type to match your packaging material and regulatory requirements.
- Match marking speed to your line rate to prevent bottlenecks or skipped codes.
- Confirm PLC communication protocols are supported by your existing control system.
- Review maintenance intervals and consumable availability to control long-term costs.
- Validate print quality on the specific material used in production, not just sample cards.
A code marking system handles the final layer of product identification. It applies date codes, batch numbers, or traceability data directly to packaging. If the mark is faint, smears, or fails to apply, the product may be rejected at the pack-out stage.
Buyers often focus on the price of the machine first. They skip the technical review. This leads to a machine that prints clean on a sample card but fails on the actual pouch, carton, or bottle in production. The gap between lab conditions and line conditions is where most marking issues appear.
What Ink Type Fits Your Packaging Material?
The ink type determines how the mark adheres to the surface. Water-based inks work well on paper and cardboard. They dry quickly and require minimal maintenance. They also face a limit. They can struggle with low energy surfaces, such as some polyethylene films or coated containers.
Thermal transfer inks use a ribbon and a heated platen or laser. They offer strong adhesion on difficult plastics and laminates. The trade-off is the consumables. Ribbon and platen wear creates a recurring cost. They also require regular cleaning to prevent clogging.
Inkjet systems use either UV or thermal inks. UV inks cure instantly with light. They are ideal for high-speed lines because there is no drying time. Thermal inks require a heated platen. They offer good adhesion but add a thermal element to the maintenance list.
Selecting the wrong ink creates a visible problem. The code may look fine under bright lights but fail a compliance check when scanned. It may also peel off during transport or handling. The ink choice must match the substrate. Test samples from your actual production run before finalizing the purchase.
How Much Resolution Do You Need for Legibility?
Resolution is measured in dots per inch. Higher numbers mean finer detail. Most modern marking systems operate between 200 and 600 dpi. The specific number matters less than the ability to print the smallest character in your code.
Regulatory labels often require a minimum font size. If you are printing a 12-point date code, a 200 dpi head will handle it easily. If you are printing a 6-point batch number, you need higher resolution to keep the lines sharp. A low-resolution head will produce blocky characters that are hard to read by the operator or the scanner.
Check the print width of the system. A head that only covers 4 inches will force you to print in sections or limit the placement of the code. On a wide carton or a long pouch, you may need a wider print area to fit all required data in one pass.
Review the minimum dot size your head can produce. This is the limit for fine lines and small characters. If the spec sheet does not list this, ask the vendor for a sample print on your specific material. Do not rely on a photo of a sample on a different surface.
What Speed Can the Marking System Maintain?
The line speed is the baseline. The marking system must apply the code at a rate that keeps up with the packaging machine. If the line runs at 150 packs per minute, the marking head must be ready to print every pack without a pause.
Some systems use a trigger-based method. A sensor detects the product, and the head fires the ink. This works well for variable speed lines. Other systems use a fixed timing method. The head prints at a set interval. This is simpler but fails if the line speed fluctuates.
Check the maximum print width per cycle. If your product is moving fast and the head must print a wide code, the head may need more time. This can force a slower line speed. The spec sheet should state the maximum line speed for the specific ink and resolution settings.
A common mistake is buying a system rated for 50 packs per minute and running it at 60. The mark will be faint or skipped. The vendor may claim the machine is rated for higher speeds, but the print quality drops. Verify the speed rating at the resolution and ink type you plan to use.
How Does the System Integrate with Your PLC?
The marking system is not an isolated device. It must talk to the rest of your line. It needs to receive data from the batch management system and confirm successful prints to the PLC.
Check the communication ports. RS232 is the standard. Ethernet is becoming common for faster data transfer. Ethernet allows the system to receive long batch numbers and confirm print status in real time.
The protocol matters. The system must support the same language as your PLC. If your PLC uses Modbus, the marking head must speak Modbus. If it uses a proprietary protocol, the integration may require a gateway or a custom interface. This adds cost and complexity.
Review the data transfer speed. If your batch numbers are short, RS232 is fine. If you are printing a QR code or a long serialized number, Ethernet will reduce the risk of data corruption. A failed data transfer means a missing or incorrect code. This is a compliance failure.
Ask the vendor for a sample integration document. It should show how the marking system connects to a standard PLC. If they cannot provide one, the integration process will be longer than expected.
What Maintenance Requirements Should You Budget For?
Maintenance is the hidden cost of a marking system. The machine itself is a small capital expense. The consumables and labor are the ongoing costs.
Inkjet systems need the head cleaned regularly. Clogged nozzles are the most common failure. The cleaning cycle can take several minutes. If it happens during production, it stops the line.
Thermal transfer systems need the ribbon and platen replaced. The ribbon wears down over time. The platen heats and cools, causing wear. The ribbon cost is a recurring expense.
Check the maintenance interval. A system that requires a cleaning every 24 hours is very different from one that requires a cleaning every 500 hours. The labor cost adds up quickly.
Review the consumable availability. If the ink or ribbon is proprietary, you are locked into that vendor. If it is a standard type, you can buy from multiple suppliers. This gives you negotiating power and ensures you are not stranded if a supplier goes out of business.
How Do You Validate Print Quality on Your Material?
The final check is a print test on your actual packaging material. The vendor will provide a sample. Do not accept it. Run the test yourself.
Print the code at your line speed. Use the exact ink and resolution settings. Check the mark under normal lighting. Check it with a scanner. Check it after the product has been handled, stored, or exposed to moisture.
A mark that looks good on a sample card may fail on a greasy or textured surface. The adhesion may be weak. The ink may migrate. The only way to know is to test on the material.
Run a durability test. Place the product in a humid environment for a few days. Check if the mark has faded or smudged. This simulates the conditions the product will face in the warehouse.
If the mark fails, go back to the ink type and resolution. Adjust the settings. Retest. Do not move to the next machine until the first one works on your material.
Criteria Table for Evaluating a Marking System
| Criterion | What to look for | Why it matters |
|---|---|---|
| Ink Type | Water-based, UV, thermal, or thermal transfer | Matches adhesion and drying requirements for your material |
| Print Resolution | Dots per inch and minimum dot size | Ensures legibility of small characters and fine lines |
| Line Speed | Maximum packs per minute at your settings | Prevents skipped codes and line bottlenecks |
| Communication | RS232, Ethernet, and PLC protocol | Ensures reliable data transfer and integration |
| Maintenance Interval | Cleaning frequency and consumable wear | Controls downtime and long-term operating costs |
| Print Width | Maximum width per print cycle | Allows full code placement in a single pass |
Final Decision Checklist
- Confirm the ink type works on your specific packaging material.
- Verify the print resolution meets your minimum character size.
- Match the maximum line speed to your current line rate.
- Check the communication protocol against your PLC.
- Review the maintenance interval and consumable availability.
- Run a print test on your actual material at production speed.
- Validate the mark with a scanner after storage and handling.
A code marking system is a small part of the line, but it carries a large amount of compliance risk. The mark is the last thing that identifies the product. If it fails, the product fails. The technical review takes a few hours. It saves weeks of downtime and rework. Use the checklist above. Test on your material. Confirm the integration. Then make the decision.
Frequently asked questions
What is the difference between water-based and UV inks for marking?
Water-based inks dry with air and are suitable for paper and cardboard. UV inks cure instantly with light, making them ideal for high-speed lines and difficult materials.
How do I know if my marking system is fast enough for my line?
Match the system's rated line speed to your current production rate. Test at your specific resolution and ink type to confirm the mark remains clear.
Can I use a marking system from a different vendor with my existing PLC?
Yes, if the marking system supports the same communication protocol as your PLC. Check the spec sheet for RS232, Ethernet, or Modbus support.
What is the most common cause of marking failure?
A mismatch between the ink type and the packaging material. The ink may not adhere properly, causing the mark to fade or peel.
How often should I clean an inkjet marking head?
This depends on the ink and the environment. Most systems require a cleaning every 24 to 500 hours. Check the maintenance manual for your specific model.


