Packaging Machinery HubWrite for us
Sizing & Throughput

How to Calculate Conveyor Length for Palletizers

Published Updated 9 min read

A palletizer conveyor system in an industrial warehouse
Quick answer

To calculate conveyor length for palletizers, measure the machine footprint, add required infeed and outfeed clearances, and account for staging areas. Verify the total against the line layout plan to ensure the conveyor matches the palletizer and surrounding equipment.

Key takeaways
  • Start with the palletizer footprint from the manufacturer's drawing, not the machine's visual width.
  • Add infeed and outfeed distances based on case size and the case packer upstream.
  • Include staging zones for manual handling or buffer capacity between machines.
  • Check the total length against the facility layout to avoid conflicts with forklifts or walls.
  • Verify the final measurement with a physical walk-through before ordering the conveyor.

Why Conveyor Length Matters for Palletizer Performance

The conveyor length determines how much product the palletizer can process without creating a bottleneck. A conveyor that is too short forces the case packer upstream to slow down. A conveyor that is too long wastes floor space and increases the cost of the installation. The goal is to find the exact distance that allows the line to run at its designed speed with a safe buffer.

This calculation is not just about the palletizer itself. It is about the entire section of the line that feeds and receives product from the palletizer. The conveyor acts as the bridge between the case packer and the palletizer, and its length must account for the physical dimensions of both machines, plus the space needed for the product to move between them.

A palletizer does not operate in isolation. It consumes cases at a specific rate and produces full pallets at a different rate. The conveyor system between the case packer and the palletizer must absorb the difference. If the case packer runs at 40 cases per minute and the palletizer can only load 35 cases per minute, the extra five cases per minute must have somewhere to go. That somewhere is the buffer on the infeed conveyor.

Conversely, if the palletizer is ready to load and the case packer is temporarily stopped for a changeover, the palletizer needs time to recover before the line stops completely. The conveyor length provides this breathing room. Without it, a minor interruption in one machine halts the entire section.

Step 1: Obtain the Palletizer Footprint Drawing

Request the installation drawing from the palletizer manufacturer. This document shows the exact width and depth of the machine, including the conveyor sections that are part of the palletizer structure. Do not rely on the visual size of the machine on the showroom floor. The drawing includes the infeed conveyor, the palletizing head area, and the outfeed section.

The footprint drawing is the primary source of truth. It is a 2D or 3D CAD file that specifies the exact dimensions from the first edge of the machine to the last. This includes the depth of the palletizing head, the width of the side panels, and the length of the integrated infeed and outfeed conveyors.

If the palletizer is modular, the footprint may vary depending on the configuration. Confirm the specific model and options with the supplier. The drawing will also show the position of the control cabinet and any hydraulic or pneumatic units that may extend the machine’s footprint.

Check the drawing for the position of the palletizing head relative to the infeed conveyor. Some models have a fixed head, while others have a rotary or multi-axis head that may require different clearance on the sides. The drawing will indicate the exact dimensions of the head area, which is critical for calculating the total length.

Step 2: Determine the Infeed Conveyor Length

The infeed conveyor carries product from the case packer to the palletizer. Its length must be sufficient to hold a buffer of product. This buffer prevents the case packer from stopping if the palletizer is temporarily interrupted.

The minimum infeed length is usually determined by the case size and the desired buffer capacity. A standard rule of thumb is to provide enough length to hold three to five cases. However, this varies based on the throughput rate. If the line runs at a high speed, you need more buffer. If the line runs slowly, less buffer is required. Check the throughput calculation for the line speed to determine the exact buffer needed.

To calculate the required buffer length, multiply the case depth by the number of cases you want to hold in the buffer. For example, if your cases are 300 millimeters deep and you want to hold four cases, you need 1200 millimeters of infeed conveyor. Add the length of the infeed section that is part of the palletizer footprint to this number to get the total infeed length.

Consider the speed of the case packer. If the case packer operates at 30 cases per minute and each case is 300 millimeters deep, the conveyor must be long enough to hold the output of the case packer during the time it takes for the palletizer to load the next case. This calculation ensures that the case packer can run at full speed without stopping when the palletizer is busy.

Step 3: Calculate the Outfeed Conveyor Length

The outfeed conveyor moves the completed pallet to the next stage of the line. This could be a forklift, a stretch wrapper, or a loading area. The length of this section depends on the distance to the next machine or the loading point.

If the palletizer discharges the pallet directly to a forklift, the outfeed conveyor may be short. If it discharges to a stretch wrapper, the conveyor must be long enough to allow the wrapper to operate without interfering with the palletizer. The manufacturer’s drawing will show the minimum outfeed length required for safe operation.

The outfeed length must also account for the pallet height. A full pallet may be 1500 millimeters high, and the stretch wrapper needs space to move its arms around the pallet. If the wrapper is a top load wrapper, it needs vertical clearance. If it is a side load wrapper, it needs horizontal clearance. The conveyor length must accommodate the wrapper’s operating radius.

Check the manufacturer’s specifications for the stretch wrapper. It will list the minimum distance from the palletizer to the wrapper. Add this distance to the length of the outfeed section that is part of the palletizer footprint. This ensures that the wrapper can operate safely and efficiently without interfering with the palletizer’s operation.

Step 4: Add Clearance for Maintenance and Safety

Do not forget the space needed for operators to access the machine. The palletizer has moving parts, sensors, and control panels that require maintenance access. The conveyor length must include enough clearance for an operator to stand safely next to the machine.

A typical clearance is 600 to 900 millimeters on each side of the conveyor. This allows an operator to inspect the belt, clear jams, and perform routine checks. If the facility has strict safety standards, you may need more clearance. Check the local regulations for the minimum distance between the conveyor and the operator.

Consider the location of the emergency stop buttons. They are usually mounted on the palletizer and the conveyor. The operator must be able to reach them quickly. The clearance must allow the operator to stand next to the machine without having to lean over the conveyor.

Check the location of the sensors and limit switches. They are usually mounted on the sides of the conveyor and the palletizer. The operator must be able to access them for cleaning and adjustment. The clearance must allow the operator to reach these components without having to climb over the conveyor.

Step 5: Account for Staging and Buffer Zones

Some lines require a staging area where product is held before it enters the palletizer. This is common in lines where the case packer and palletizer have different cycle times. The staging zone acts as a buffer, allowing the two machines to run at their own speeds without stopping each other.

The length of the staging zone depends on the capacity required. A common size is 2000 to 4000 millimeters, but this varies. If the line has a high throughput rate, the staging zone may need to be longer. If the line has a low throughput rate, a shorter staging zone may be sufficient.

The staging zone is usually a separate conveyor section that is not part of the palletizer footprint. It is located between the case packer and the palletizer. It must be long enough to hold the product during the time it takes for the palletizer to load the next case.

Check the throughput calculation for the line speed. If the case packer runs at 40 cases per minute and the palletizer runs at 35 cases per minute, the staging zone must hold five cases per minute. Multiply this by the case depth to get the required length. Add this to the infeed length to get the total length.

Step 6: Sum the Components to Find Total Conveyor Length

Add the infeed length, the palletizer footprint, the outfeed length, and the staging zone length to get the total conveyor length. This sum is the distance from the start of the infeed conveyor to the end of the outfeed conveyor.

For example, if the infeed is 1500 millimeters, the palletizer footprint is 3000 millimeters, the outfeed is 1000 millimeters, and the staging zone is 2000 millimeters, the total length is 7500 millimeters. This is the length you need to order from the conveyor supplier.

Check the total length against the floor plan. Make sure it fits between the walls, forklift paths, and other equipment. A conveyor that is too long may block a forklift path or interfere with a stretch wrapper. A conveyor that is too short may leave a gap that causes product to fall off.

Adjust the staging zone or the infeed length to fit the space. If the floor plan is tight, you may need to reduce the staging zone or use a more compact palletizer. If the floor plan is open, you may need to increase the staging zone to allow for a higher throughput rate.

Step 7: Verify Against the Line Layout

Take the total length and place it on the line layout drawing. Check if it fits between the walls, forklift paths, and other equipment. A conveyor that is too long may block a forklift path or interfere with a stretch wrapper. A conveyor that is too short may leave a gap that causes product to fall off.

Walk the floor with a measuring tape. Mark the start and end points of the conveyor. Check if the length matches the drawing. If there is a discrepancy, adjust the staging zone or the infeed length to fit the space.

Check the height of the conveyor. It must match the height of the case packer and the palletizer. If the conveyor is too high, the case packer will not be able to load the cases. If the conveyor is too low, the palletizer will not be able to load the cases. Check the manufacturer’s specifications for the required height.

Common Mistakes in Conveyor Length Calculation

One common mistake is using the visual width of the palletizer instead of the footprint from the drawing. The visual width may be 2000 millimeters, but the footprint may be 3000 millimeters due to the infeed and outfeed sections.

Another mistake is ignoring the staging zone. Many engineers calculate the conveyor length as the distance between the case packer and the palletizer. This leaves no buffer, causing the line to stop frequently.

A third mistake is not checking the clearance for maintenance. If the conveyor is too short, the operator cannot access the side of the palletizer. This leads to safety issues and longer maintenance times.

A fourth mistake is not checking the height of the conveyor. If the conveyor is too high or too low, the case packer and the palletizer will not be able to load the cases. This leads to jams and stoppages.

Final Verification Step

Before ordering the conveyor, perform a physical verification. Place the conveyor on the floor in its final position. Run the line for a short period. Check if the product moves smoothly from the case packer to the palletizer and then to the outfeed. Check if the operator has enough space to stand next to the machine. If everything works, the conveyor length is correct.

If the product stops or the operator has to lean over the machine, adjust the length. Re-run the line and check again. This verification step ensures that the conveyor length is not just calculated on paper, but works in the real world.

Table: Typical Conveyor Length Components

Component Typical Length Reason
Infeed Conveyor 1500 - 3000 mm Buffer for product from case packer
Palletizer Footprint 2500 - 4000 mm Machine structure and operation area
Outfeed Conveyor 1000 - 2000 mm Distance to next machine or loading point
Staging Zone 2000 - 4000 mm Buffer for speed mismatch
Maintenance Clearance 600 - 900 mm Safe access for operators

Frequently asked questions

How do I know if the conveyor is too short?

If the case packer stops frequently because the infeed conveyor is empty, the conveyor is too short. Also, if the operator cannot stand safely next to the machine, the clearance is insufficient.

Can I use a shorter conveyor to save space?

Yes, but only if the line throughput is low and the case packer can handle short stops. For high throughput lines, a shorter conveyor will cause bottlenecks and reduce output.

What if the palletizer footprint is larger than the drawing shows?

Contact the manufacturer. The footprint may include options that were not in the original drawing. Confirm the specific configuration before calculating the conveyor length.

Is the staging zone always required?

No. If the case packer and palletizer have the same cycle time, a staging zone may not be needed. However, it is recommended for most lines to provide a safety buffer.

How do I verify the conveyor length without running the line?

Use a measuring tape to mark the start and end points on the floor. Check the distance against the drawing. Walk the floor and check for clearances and obstacles. ===END===